达州做网站
大橙子网站建设，新征程启航
为企业提供网站建设、域名注册、服务器等服务
NAT实验组合实战-静态+端口映射-创新互联
NAT实验组-静态+端口映射
静态NAT
拓扑图如下：
实验步骤
1、设置sw三层交换机
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
sw(config)#no ip routing //关闭路由功能
sw(config)#2、设置路由R1
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#int f0/0
R1(config-if)#ip add 192.168.10.1 255.255.255.0 //仅设定IP地址与子网掩码
R1(config-if)#no shut
*Mar 1 00:03:21.575: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar 1 00:03:22.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#int f 0/1
R1(config-if)#ip add 8.0.0.1 255.0.0.0 //仅设定IP地址与字网掩码
R1(config-if)#no shut
*Mar 1 00:03:42.443: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar 1 00:03:43.443: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R1(config-if)#ex
R1(config)#ip route 0.0.0.0 0.0.0.0 8.0.0.2 //设置默认路由
R1(config)#do show ip route //查看路由表
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is 8.0.0.2 to network 0.0.0.0
C 192.168.10.0/24 is directly connected, FastEthernet0/0
C 8.0.0.0/8 is directly connected, FastEthernet0/1
S* 0.0.0.0/0 [1/0] via 8.0.0.2
R1(config)#3、设置路由R2
R2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#int f 0/1
R2(config-if)#ip add 8.0.0.2 255.0.0.0 //仅设定IP地址与子网掩码
R2(config-if)#no shut
R2(config-if)#int f 0/0
R2(config-if)#
*Mar 1 00:05:13.815: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar 1 00:05:14.815: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R2(config-if)#ip add 192.168.200.1 255.255.255.0 //仅设定IP地址与字网掩码
R2(config-if)#no shut
R2(config-if)#
*Mar 1 00:05:40.643: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar 1 00:05:41.643: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R2(config-if)#ex
R2(config)#ip route 192.168.10.0 255.255.255.0 8.0.0.1 //设置静态路由
R2(config)#do show ip route //查看路由表
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
S 192.168.10.0/24 [1/0] via 8.0.0.1
C 192.168.200.0/24 is directly connected, FastEthernet0/0
C 8.0.0.0/8 is directly connected, FastEthernet0/1
R2(config)#4、设定三台PC机
PC1
PC1>
PC1> ip 192.168.10.10 192.168.10.1
Checking for duplicate address...
PC1 : 192.168.10.10 255.255.255.0 gateway 192.168.10.1
PC1>PC2
PC2>
PC2> ip 192.168.10.20 192.168.10.1
Checking for duplicate address...
PC1 : 192.168.10.20 255.255.255.0 gateway 192.168.10.1
PC2>PC3
PC3>
PC3> ip 192.168.200.20 192.168.200.1
Checking for duplicate address...
PC1 : 192.168.200.20 255.255.255.0 gateway 192.168.200.1
PC3>此时，整个实验结构已完成，已经可以做到全网互通，参考如下：（如不能联通，请自行检查）
为满足实验目的，接下来将进行静态NAT的设置
在R1上设置静态NAT
R1(config)#ip nat source static 192.168.10.10 8.8.8.8 //静态NAT1
*Mar 1 00:13:12.995: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to up
R1(config)#ip nat source static 192.168.10.20 8.8.8.10 //静态NAT2
R1(config)#int f 0/0
R1(config-if)#ip nat inside //启用外部NAT
R1(config-if)#int f 0/1
R1(config-if)#ip nat outside //启用内部NAT
R1(config-if)#实验完成\~\~\~\~\~
静态NAT-端口映射
拓扑图如下：
实验步骤
1、设置Linux服务器
将端口进行绑定，绑定在VMnet1上，并设置静态IP
[root@localhost ~]# vim /etc/sysconfig/network-scripts/ifcfg-ens33
改dhcp为static
在末行按o在下行插入
IPADDR=192.168.100.100
NETMASK=255.255.255.0
GATEWAY=192.168.100.1
[root@localhost ~]# service network restart
Restarting network (via systemctl): [ 确定 ]
[root@localhost ~]# ifconfig
ens33: flags=4163 mtu 1500
inet 192.168.100.100 netmask 255.255.255.0 broadcast 192.168.100.255 安装http服务并自定义首页
[root@localhost ~]# yum install httpd -y
[root@localhost ~]# vim /var/www/html/index.html //写测试网页
this is inside web
[root@localhost ~]# systemctl start httpd
[root@localhost ~]# systemctl stop firewalld.service
[root@localhost ~]# setenforce 02、设置路由R1
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#int f 0/0
R1(config-if)#ip add 192.168.10.1 255.255.255.0 //仅设置IP地址和子网掩码
R1(config-if)#no shut
*Mar 1 00:00:44.895: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
*Mar 1 00:00:45.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
R1(config-if)#int f 0/1
R1(config-if)#ip add 8.0.0.1 255.0.0.0 //仅设置IP地址和子网掩码
R1(config-if)#no shut
R1(config-if)#ex
*Mar 1 00:01:03.159: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar 1 00:01:04.159: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
R1(config-if)#ex
R1(config)#3、设置Host2主机
绑定VMnet2，并设置静态IP
此时，通过在浏览器在输入192.168.100.100，即可访问对方网页
为了满足实验要求，下面将进行端口映射
R1
R1(config)#ip nat inside source static tcp 192.168.100.100 80 12.0.0.100 8080 extendable R1(config)#int f0/0
R1(config-if)#ip nat inside
R1(config-if)#int f0/1
R1(config-if)#ip nat outsid
R1(config-if)#end
R1#debug ip nat
IP NAT debugging is on
*Mar 1 00:36:59.327: NAT*: TCP s=49160, d=8080->80
*Mar 1 00:36:59.327: NAT*: s=12.0.0.12, d=12.0.0.100->192.168.100.100 [364]
//端口和地址都进行了转换验证结果
使用Host2主机再次进行访问，输入http://12.0.0.100:8080同样可以访问。
另外有需要云服务器可以了解下创新互联cdcxhl.cn，海内外云服务器15元起步，三天无理由+7*72小时售后在线，公司持有idc许可证，提供“云服务器、裸金属服务器、高防服务器、香港服务器、美国服务器、虚拟主机、免备案服务器”等云主机租用服务以及企业上云的综合解决方案，具有“安全稳定、简单易用、服务可用性高、性价比高”等特点与优势，专为企业上云打造定制，能够满足用户丰富、多元化的应用场景需求。
分享名称：NAT实验组合实战-静态+端口映射-创新互联
URL链接：http://dzwzjz.com/article/dopidh.html